Before you start
Safety comes first, and this applies to any marker:
- Remove the gas source. Disconnect the CO2 or HPA tank before you disassemble anything. Kingman’s manual lists this as a standing warning.
- Take the hopper off and clear all paint from the feed neck and breech.
- Treat the marker as loaded until you have confirmed it is empty. Never look down the barrel.
- Fire the remaining air in a safe direction with the barrel pointed away from people, if your manual advises it, and keep a barrel blocker on when you are finished.
- Work on a clean, flat surface where small parts will not roll away.
Use this guide as a general overview. Your marker’s manual is the final word, especially since Spyder parts and designs have changed over the years.
What you’ll need
- Your owner’s manual or an exploded parts diagram
- A clean, lint-free cloth or paper towels
- A barrel swab
- Marker-safe lubricant. Check which type your manual recommends, and avoid using whatever oil is nearby.
- Allen keys, if your model has screws you need to remove
- A small tray for parts
Step-by-step disassembly
The Victor is generally described as easy to field-strip, with a tool-free striker plug and a pull-pin top-cocking bolt. Exact steps can vary by model year, so treat this as the typical sequence.
- Remove the barrel by unscrewing it from the front of the body.
- Swab the barrel and set it aside.
- Remove the striker plug at the rear of the marker. On the Victor it is designed to come out without tools.
- Remove the striker and spring, noting their order and orientation.
- Remove the bolt. On top-cocking Spyders the bolt is typically worked out of the body after the cocking pin is released. Take care not to force anything.
- Lay the parts out in the order you removed them.
If something does not move easily, stop and check the manual. Forcing a part is the most common way to damage a marker.
Cleaning the parts
- Wipe the bolt and the inside of the body tube with a clean cloth.
- Remove broken paint and shell residue from the breech and feed neck. Warm, damp cloths work well for fills and fragments.
- Swab the barrel from the back to the front until the swab comes out clean.
- Inspect each O-ring for cuts, flattening or dryness. Worn O-rings are a common cause of leaks and low velocity.
Avoid soaking the marker or putting it in water, and avoid harsh solvents, which can damage seals.
Lubricating
Apply a small amount of marker-safe lubricant to the O-rings and any moving surface the manual recommends. Too much oil attracts dirt and paint and can make shots inconsistent. Wipe off any excess.
Putting it back together
Reassemble in the reverse order:
- Bolt
- Striker and spring
- Striker plug
- Barrel
Make sure each part is seated fully. Cock and release the marker a few times without gas to check it moves freely and the trigger resets.
Test and tune
Reconnect the gas source and check for leaks, such as hissing from the body or feed neck. Fire a few shots at a safe target, then check your velocity on a chronograph. Fields set their own limits, so check what your field requires. The Victor has an external velocity adjuster, so you can usually tune it without disassembly. If you are shopping for a Victor or comparing it with another Spyder, our Victor vs MR100 comparison may help.
How often to clean
A quick wipe-down after each day of play is a good habit. Give it a fuller clean after a paint break inside the marker, after playing in wet or dusty conditions, or if you notice shots dropping in consistency. Lubricate lightly every so often rather than heavily every time.
Common problems after a clean
- Air leaks: a missing, pinched or dry O-ring is the usual cause. Reseat or replace it.
- Low or erratic velocity: check the velocity adjuster, the striker spring and the lubricant level.
- Trigger does not reset: a part is likely out of order or not seated.
- Paint chopping: check the feed neck and make sure the barrel is clean and suits your paint.
For a broader look at the marker and its siblings, see our guide to Spyder paintball guns.